Equipment, instrumentation, engine G3520, and g3516 and g3524 Caterpillar, CAT, MTU

Equipment, instrumentation, engine G3520, and g3516 and g3524 Caterpillar, CAT, MTU

Electric motor, the direction of the starter with a voltage of 23 volts, and stream 115 amps سوییچ magnetic voltage 24 VDC, and flow, 1.3 amps DIsconnect Switch with the flow of the illustrious 1000 amps and 0.3 volts سنسور temperature Operating Temperature 40 - to 120 degrees and voltage is 4.5 volts سنسور temperature(thermocouple) With average performance of 40 - Eli 1095 degrees Celsius سنسور temperature with the average performance of the 40 - Eli 125 degrees centigrade, and the voltage of 5 V DC and the flow of 10 MA سنسور pressure سنسور pressure with average performance of 40 - Eli 125 degrees Celsius and maximum pressure of 1135 کیلوپاسکال and flow, maximum of 20 MA سنسور hit with a voltage of 8 v Dc and the flow of 30 Ma سوییچ pressure input جکت water سنسور speed on current motor with voltage of 12V سنسور engine speed جعبه connection includes 3 MCB, with the flow of the DC

: this module often فانکشنهای motor controls, and different inputs from the sensors for ActiveX relay, and سلنوئیدها monitor does. The primary duty of the ECM master include the following: کنترل engine speed کنترل the ratio of fuel and Air سکوئنسهای starter and steppe حفاظت and monitoring engine کنترل combustion and دتونشن cylinder left Slave ECM: this is the ignition control module and دتونشن cylinder, the right side controls.

کنترل speed engine: ECM master control اکتواتور in command to تروتل optimum speed موتوررا saprt works. This command from the ECM to اکتواتر some stream, consume that ET is visible. سرعت desirable engine under the influence of some parameters such as status, speed keys, scattered Cargo /Speed, name, etc. input speed optimal(ولتاز analog or a current between 4 to 20 milliamps), the maximum engine speed, the cargo, etc. (which software is), the speed of the real engine by the speed sensor, the time measured by the parameters such as the coefficient of interest for governor, which by the ET set can be

کنترل air / fuel ratio: the ECM master fuel ratio change to produce less polluting emissions, the control of them. This system of a Volvo fuel metering and driver output Ecm master, and the map is composed. This system for the process emission rate changes btu fuel controls. مراحل the performance of this system are: ECM master speed فلوی air and fuel by a factor 1-speed optimal موتور2-speed real موتور3-time calculation of the motor determines the میزان Flo fuel by Link CAN to the Volvo fuel level measurement is sent.

سکوئنس starter and the steppe: ECM Master includes a hard drive and خروجهای the starter and the engine can be. Hard drive customizable client signals sent from the components below gives the answer : کنترل engine سوییچ steppe, emergency دیتا link when the hard drive customizable by کاستمر determine that the engine should be set up should ... the ECM master the positive pole batteries to the relays, starter motors, DC connects زمانی that the speed of the terminal Karnak customizable to the optimal amount of receipt or a period of time, Karnak customizable all the ... the ECM voltage cut them. ولو shot of F-gas should be, or by equipping the customer's own electrical data, or by the control system of the engine, in case the second choice ECM master control of the polarity of positive ولتاز on the Volvo and the timing of it, according to the hard drive the customer is also responsible for takes place.

حفاظت and monitoring: ECM master also protecting the electrical system of the engine and its performance monitor does.

The functional, because of low pressure oil, a Error Code gives out that ECM, Mastercard, can ...